Bladerf 2.0 micro xA4

BLADERF 2.0 MICRO XA4 SHORT DESCRIPTION
The Bladerf 2.0 micro xA4 is the ultimate SDR platform for pentesters and researchers.
MITM GSM traffic. Manipulate GPS. Capture and replay Remote Controls, and much more.
INTRODUCTION
BladeRF 2.0 Micro xA4 is the undisputed SDR champion, boasting unmatched frequency range, huge bandwidth, incredible on-board processing capacity backed with full software support.
For penetration testers, the killer-feature is the ability to run 3G/LTE Base-Stations via OpenBTS, allowing testing, manipulation and MITM for cellular IOT devices.
The Standard Pack contains everything needed to build a BTS: RX and TX amplifiers and 4x GSM antennas. The Deluxe Pack contains 4x Wide-Band general purpose antennas to extend your testing surface.
The BladeRF is a mature, wide-band full duplex 2×2 MIMO RF transceiver, covering 47MHz to 6GHz.
It is compatible with all major SDR suites across multiple platforms: GNU Radio via gr-osmosdr, Pothos via SoapySDR, SDRange, SDR Console, SDR # via sdrsharp-bladeRF, MathWorks MATLAB® & Simulink® via libbladeRF bindings.
BladeRF libraries, utilities, firmware and HDL are open source with public schematics. There are extensive SDKs available free of charge.
The wide-band range, extensive bandwidth and full duplex capabilities make the BladeRF the ideal tool for multiple use-cases:
Remote Control Analysis: Analyse, replay and emulate car remotes, alarms, garage remotes, etc.
GPS Manipulation: Block, manipulate or adjust GPS signals for location-aware devices
MITM GSM devices: Capture and manipulate data from cellular IOT devices.
Advanced RFID Analysis: Analyse and communicate with all RFID tags, regardless of their frequency.
Standard SDR functionality: ADB-S Tracking, satellite-communication, packet-sniffing, signal analysis, etc
USB 3.0 SUPERSPEED
Capture & process at 5Gbps full-duplex
ONBOARD PROGRAMMABLE FPGA
Write apps directly on-board.
BUILT FOR PROFESSIONALS
Built to exceed standards and expectations.
COMMUNITY BACKED
Plug’n’Play compatible with all major SDR suites.
READY TO GO
Comes with everything, including antennas.
Lab401 provides two BladeRF configurations or packs.Use our guide below to understand which pack is best suited to your needs.
Starter Pack
The Starter Pack provides the minimum configuration required for creating a BTS in laboratory conditions. The BladeRF’s powerful architecture has made it the “go-to” BTS solution. If you’re looking to get started with GSM/S7/OpenBTS hacking – this is the pack for you.
Deluxe Pack
Built on the foundations of the Starter Park, the Deluxe Pack provides the complete SDR & BTS configuration – in the laboratory and in the field.
With a full-range of antennas and and two amplifiers, the Deluxe Pack is aimed for real-world SDR exercises and in-the-field BTS pen-test operations – and everything in between.
The full pack breakdown is below:
Product
Starter
Deluxe
Description
BladeRF 2.0 micro xA4
✔️
✔️
BladeRF Mainboard: 47MHz to 6GHz frequency range
BladeRF Case
✔️
✔️
Clear Polycarbonate case
GSM Antenna (x2)
✔️
GSM Antennas optimised for BTS usage
GSM Antenna (x4)
✔️
GSM Antennas optimised for BTS usage
BT-100 Bias-Tee Amplifier (x2)
✔️
Wideband bias tee TX Power Amplifier
BT-200 Bias Tee Amplifier (x2)
✔️
BT-200 is a wideband bias-tee RX Low Noise Amplifier
Tri-Band Antenna (x4)
✔️
General purpose tri-band antenna that covers 700MHz to 2600MHz
RF Specifications
Min
Max
Unit
ADC/DAC Sample Rate
0.521
61.44
MSPS
ADC/DAC Resolution
12
bits
RF Tuning Range (RX)
70
6000
MHz
RF Tuning Range (TX)
47
6000
MHz
RF Bandwidth Filter
<0.2
56
MHz
CW Output Power
+8
dBm
FPGA Specifications
Min
Max
Unit
Logic Elements
49
kLE
Memory
3,383
kbits
Variable-precision DSP blocks
66
342
Embedded 18×18 Multipliers
132
684
Starter Pack
1x bladeRF 2.0 micro xA4
1x bladeRF 2.0 micro case
2x GSM Antennas
1x USB 3.0 SS Cable
Deluxe Pack
1x bladeRF 2.0 micro xA4
1x bladeRF 2.0 micro case
1x BT-100 Bias-Tee TX Amplifier
1x BT-200 Bias-Tee RX Amplifier
4x GSM Antennas
4x Tri-Band General Purpose Antennas
1x USB 3.0 SS Cable
Each bladeRF is dispatched from Europe – no need to worry about slow shipping times, import duties or damaged goods.
Packed in a sturdy compact 85x130x45mm box.
We provide worldwide shipping with express options.
Windows/macOS/Linux/Android (Specific Builds)
GNU Radio via gr-osmosdr, Pothos via SoapySDR, SDRange, SDR Console, SDR # via sdrsharp-bladeRF, MathWorks MATLAB® & Simulink® via libbladeRF bindings.
Technical Documents
bladeRF Product Brief
libbladeRF API documentation
An SDR-Based FRS Transceiver (PDF)
GNU Radio flowgraph is available here
Firmware Images
FPGA bitstreams
FX3 firmware
Useful Links
Source code on GitHub
bladeRF Wiki
bladeRF VCTCXO factory calibration lookup
SDR-Radio
SDRAngel
Airspy
SRS-LTE
OpenAirInterface (Ensure you use `develop’ branch)
SDR# Github
SDR# precompiled binaries
YateBTS installation instructions (v1.0 only)
Yate and YateBTS source code tarball with readme (v2.0) use v1.0 instructions (link above) RC (LATEST)
Yate and YateBTS source code tarball with readme (v2.0) use v1.0 instructions (link above)